Polystyrene board system for powder Features JMH-02 polystyrene board system for powder, the powder by high temperature, high pressure, and with a variety of spray-dried powder imports increased activity of homo-made, enabling significantly improved adhesive mortar and polystyrene board bonding capacity (adsorption bond) and their tensile strength, resistance to fall, good water retention properties thickening construction, water, freeze-thaw resistance, heat aging performance outstanding, ingredients simple, easy to use, an low cost. Physical and chemical properties Product Description JMH-02 polystyrene board system for powder cement-based series of building materials for specific products, this product has excellent integration of cement, can be completely dissolved in the cement mortar paste mixed backbone, not reduced after curing strength of cement, while maintaining a cohesive effect, the film resistance and flexibility, but also has good weather resistance and stability. With the most obvious advantage of this product is its superior bonding properties and crack resistance, after drying, can effectively prevent the erosion of the wall of acidic air, after a difficult subject to wet powder, deliquescence, is widely used to bond mortar, cracking mortar wall materials, and can dramatically lower the cost of production. Application examples 1. adhesive mortar (EPS board insulation system) produce reference formula ① PO42.5 ordinary Portland cement 400KG / T ② quartz sand 600KG / T ③ JMH-02 polystyrene board system for powder 10KG / T ④ HPMC 0- 2KG / T ⑤ lignocellulosic 1-2KG / T directly add water and stir evenly, water-cement ratio of 20 to 22%, for 5 to 10 minutes can be used to prohibit construction in temperatures below 5 ℃, time is best used within 30 minutes the adhesive thickness of 3-5mm, 28 days can reach 80% of the solidification bonding effect, with about 5 KG / m. Construction quality parameters Reference: "JGJ / 144-2004 exterior insulation engineering point of order" Product Quality Reference: "JG149-2003 expanded polystyrene board thin plaster exterior insulation system" 2 surface mortar (EPS board insulation system ) Production Reference formula ① PO42.5 ordinary Portland cement 350-400KG / T ② quartz sand 600-650KG / T ③ JMH-02 polystyrene board system for powder 10KG / T ④ HPMC 1-3KG / T ⑤ polypropylene fibers 1.5 KG / T ⑥ lignocellulosic 3KG / T directly add water and stir evenly, water-cement ratio of 20 to 22%, for 5 to 10 minutes can be used. Construction standards: polystyrene board overlay layer of mortar thickness 2 ~ 3mm, mesh affixed to flatten solid cast after 1 ~ 2mm thick mortar, reinforced portion 5 ~ 7mm thick, 28 days can reach 80% of the solidified sticky knot effect, with about 5KG / m. Construction quality parameters Reference: "JGJ / 144-2004 exterior insulation engineering point of order" Product Quality Reference: "JG149-2003 expanded polystyrene board thin plaster exterior insulation system" Notes: 1. feeding should not be a one-time investment; 2. must be added to the polypropylene fiber, first into the cement dispersed as small particles of cement fiber can eliminate static electricity, in order to make polypropylene fibers dispersed; 3. mixing evenly, but not too long mixing time 15 minutes is appropriate, for a long time stirring the sand and cement easily precipitate stratification (vertical mixer special attention); 4. according to seasonal changes need to adjust the amount of additives; 5. Avoid moisture caking additives or cement; 6. Do mixed with acidic substances stacked use; below 7.5 ℃ prohibit the use of construction, low construction quality of the project will cause the biggest problems, resulting in surface mortar and insulation board without bond, this is no project late remedy quality problems. 1.25 KG Packaging and storage containers, paper and plastic bags chemical compound lined PVC film; 2. shelf life of two years, to be waterproof, must be sealed Zhakou After unpacking, odorous, non-toxic. Description: adhesive mortar adhesive mortar powder price consultation today it is accompanied by concrete, quartz sand, polymer binder additives made by mechanical mixing. Mainly used for bonding adhesive insulation board, also known as polymer insulation board adhesive mortar. The specially modified adhesive mortar made of high quality cement and a variety of polymer materials, filler composite made through a unique process, water retention, high adhesive strength. Main features one: with the primary wall and polystyrene board insulation board, etc. have a strong bonding effect. Two: water and freeze-thaw resistance, anti-aging properties. Three: construction convenient, is a very safe and reliable insulation system adhesive material. Four: construction not Huazhui. Has excellent weather, impact and cracking performance. The main purpose for interior walls, exterior walls and ceiling of bonding polystyrene board and rock wool board, extruded insulation board and other boards. A: The base requirements: smooth, firm, dry and clean. New plaster layer after at least 14 days before curing and drying after construction (base flatness of less than 2-5 mm one square meter). II: Preparation of material: 25-30% by weight of the feed ratio of added water (add water to adjust the visual basic level and climatic conditions), to stir, mixing materials should be used within two hours. Three: the amount of bonded polystyrene board are 4-5 kg ??one square meter. According to wall formation conditions, the use of the entire surface of the bonding method or the two-point frame method bonding methods polystyrene board. A: the entire surface bonding: flatness requirements apply to less than 5 mm square of a grass-roots level. Plastering with serrated knife to smear adhesive insulation board, then bottom-bonded insulation board on the wall, board formation, pressing seams void. Bonding point box method:: B does not apply to the flatness of less than 10 mm square meters of uneven grass roots. Plastering knife with adhesive evenly onto the insulation board edge, and then evenly distributed on the plate six bonding points, depending on the thickness of the wall painting flatness OK. Then by the above method sticking to the wall plate. The proportion of adhesive mortar with water about 4: 1 (weight ratio)), to stir. Reference dosage: 4 ~ 6kg / m2 primary wall must be flat, solid, clean and dry. Paint layers and layers of loose parts of the primary wall plaster surface must be removed. New painting plaster layer must dry after hardening before use. With a plaster knife to wipe insulation board adhesive mortar, the insulation board and then bottom-kneaded paste evenly to the base wall, the board should be flat, slab should be compacted to void. With 2m by foot inspection flatness, there can glue between the seams. Paste ways: point edge Paste or strips pasted stickers area ≥40% of the entire board area. This product is installed in the brown paper bag, net weight 40 kg each bag. 5 ~ 30 ℃ under the conditions of storage, the storage period of six months, sunscreen, pay attention to water, non-dangerous goods for transportation. Placed on pallets stored off the ground to avoid rain soaked to ensure ventilation and dry. Avoid direct sunlight. Note A: adhesive mortar in proportion with stirring, according to the construction site on the viscosity of the mortar to adjust to. Two: the construction environment and the primary wall temperature of not less than 5 ℃, wind 5 below, to avoid the rain construction. Three: When you paste insulation board even rubbing pressure, not rattling. Four: Paste completed within 48 hours, can not be a process under construction, and should avoid touching, percussion, vibration. Five: In the case of wind or rain than 5 should take protective measures. Six: good mixing mortar should be used within 2 hours, the solidified hardened mortar can not be used a second time. Seven: the construction site is strictly prohibited without permission to add sand, cement and other additives. It is accompanied by adhesive mortar cement, quartz sand, polymer binder additives made by mechanical mixing. Mainly used for bonding adhesive insulation board, also known as polymer insulation board adhesive mortar. The specially modified adhesive mortar made of high quality cement and a variety of polymer materials, filler composite made through a unique process, water retention, high adhesive strength. Main features one: with the primary wall and polystyrene board insulation board, etc. have a strong bonding effect. Two: water and freeze-thaw resistance, anti-aging properties. Three: construction convenient, is a very safe and reliable insulation system adhesive material. Four: construction not Huazhui. Has excellent weather, impact and cracking performance. The main purpose for interior walls, exterior walls and ceiling of bonding polystyrene board and rock wool board, extruded insulation board and other boards. A: The base requirements: smooth, firm, dry and clean. New plaster layer after at least 14 days before curing and drying after construction (base flatness of less than 2-5 mm one square meter). II: Preparation of material: 25-30% by weight of the feed ratio of added water (add water to adjust the visual basic level and climatic conditions), to stir, mixing materials should be used within two hours. Three: the amount of bonded polystyrene board are 4-5 kg ??one square meter. According to wall formation conditions, the use of the entire surface of the bonding method or the two-point frame method bonding methods polystyrene board. A: the entire surface bonding: flatness requirements apply to less than 5 mm square of a grass-roots level. Plastering with serrated knife to smear adhesive insulation board, then bottom-bonded insulation board on the wall, board formation, pressing seams void. Bonding point box method:: B does not apply to the flatness of less than 10 mm square meters of uneven grass roots. Plastering knife with adhesive evenly onto the insulation board edge, and then evenly distributed on the plate six bonding points, depending on the thickness of the wall painting flatness OK. Then by the above method sticking to the wall plate. The proportion of adhesive mortar with water about 4: 1 (weight ratio)), to stir. Reference dosage: 4 ~ 6kg / m2 primary wall must be flat, solid, clean and dry. Paint layers and layers of loose parts of the primary wall plaster surface must be removed. New painting plaster layer must dry after hardening before use. With a plaster knife to wipe insulation board adhesive mortar, the insulation board and then bottom-kneaded paste evenly to the base wall, the board should be flat, slab should be compacted to void. With 2m by foot inspection flatness, there can glue between the seams. Paste ways: point edge Paste or strips pasted stickers area ≥40% of the entire board area. This product is installed in the brown paper bag, net weight 40 kg each bag. 5 ~ 30 ℃ under the conditions of storage, the storage period of six months, sunscreen, pay attention to water, non-dangerous goods for transportation. Placed on pallets stored off the ground to avoid rain soaked to ensure ventilation and dry. Avoid direct sunlight. Note A: adhesive mortar in proportion with stirring, according to the construction site on the viscosity of the mortar to adjust to. Two: the construction environment and the primary wall temperature of not less than 5 ℃, wind 5 below, to avoid the rain construction. Three: When you paste insulation board even rubbing pressure, not rattling. Four: Paste completed within 48 hours, can not be a process under construction, and should avoid touching, percussion, vibration. Five: In the case of wind or rain than 5 should take protective measures. Six: good mixing mortar should be used within 2 hours, the solidified hardened mortar can not be used a second time. Seven: the construction site is strictly prohibited without permission to add sand, cement and other additives. Excellent quality is the last word company statement, there is no question of powder factory strict quality corporate purpose; user credibility of the first quality first corporate philosophy; the best products delivered to the client company declares : a signed product quality assurance and undertaking - substandard products not manufactured. 2, within two years of product quality tracking service, and customer service records stored in the archives for 20 years. 3 Ensure product quality problems, I will guarantee, refunding, replacement, meet customer requirements.