Ash calcium powder inside the base for the external walls of water putty, wall putty flexible, waterproof putty products, the products and cellulose, calcium gray and white cement has excellent fusion can be completely dissolved in the putty paste. Both have excellent adhesion and film-forming role effectively supplement cellulose adhesion and drying to form an impermeable coating to solve putty and scrape off the surface is not smooth problems, but also has good weather resistance and stability after difficult by wet powder, deliquescence, back to yellow, is widely used in water putty, waterproof putty, flexible putty, and many other wall materials. Application examples: external flexible, water-resistant putty reference formula ① white cement 300KG / T ② ash calcium 50KG / T ③ GCC 650KG / T ④ HPMC 5KG / T ⑤ exterior wall putty powder 10KG / T ⑥ polypropylene fibers 1.5KG / T (direct plus water Stir for 5 to 10 minutes to use). Quality parameters of product quality reference: P-type: "JG / T157-2004 standard" R-type: "JG / T229-2007 standard" Notes: 1. Feeding time investment should not; 2. Need to adjust according to seasonal changes additives dosage; 3. Avoid moisture caking additives or fillers; 4. Non-acidic substances mixed stacking, use. 1.25KG packaging and storage equipment, paper and plastic bags chemical compound lined PVC film; 2. shelf life of two years, to be waterproof, must be sealed Zhakou After unpacking, odorous, non-toxic and modern high-performance new materials and putty technical one, timber exploitation of natural activity and the ability to gel materials, such as clay, silicon, aluminum, calcium, magnesium mineral material composition, natural polymers (such as ecological functions HYM-2 type can be dispersed resin powder etc.). Attached: HYM-22 resin-based ecological functions can be dispersed powder technical performance and the scope of (1) health and safety standards and environmental protection index test project value (First grade) Found formaldehyde (mg / kg) ≤100 not detected VOC (mg / kg) ≤15 BTEX sum (mg / kg) were not detected ≤300 not detected lead, cadmium, chromium, mercury (mg / kg) ≤285 Not detected radioactivity (GB6566-2001) in Class A Indicators were not detected anti-bacterial, fungal properties (HG / T3950--2007) 0 stage (2) fire performance combustion performance level (GB8624-2006) B1-B2-stage combustion toxicological drip, does not produce dust and drama toxic smoke (3) Technical Specifications Appearance white powder Viscosity (23 ± 2 ℃), pa.s ℃ ≥1.00 ≥1.1-4.3 180 ° peel strength N / 25mm ≥10 ≥12-33 bond strength MPa ≥0.5 ≥0.8-1.1 low temperature stability (0 ℃ 24h) showed a flow state (4) stability of powdered finished product storage stability of 1-3 years (at room temperature sealed.) aqueous solution (powder: water ratio = 1: 9) 6- December (at room temperature. Seal) (5) Scope HYM-22 ecological function type can be dispersed resin powder is suitable for the production of a variety of interior and exterior wall putty powder products. Add about 0.2-1%. 2, technical principles clay, mineral material mainly active substance, with a small amount of HYM-2 ecological functions dispersible type resin powder, etc. from the gel reaction, generating a new gel composition, belonging to the geopolymer category, the gel reactant generation, clay, mineral filler material is both, and is a gel material and ecological functions HYM-22 resin type dispersible powder and clay mineral material after gel formation reaction, will produce dural plastic, reinforced structural strength and stability of the base surface and the wall putty adhesive ability with putty, with temperature and humidity, sound insulation, fire, earthquake, waterproof, moisture-proof, anti-bacterial, air purification, very increase living comfort and other large extent. 3. Research and application of modern architecture with putty, extensive use of CMC, MC, HPMC and other cellulose-based products and chemical latex, powdered polyvinyl alcohol and other raw materials, large-scale use of these products, consume a lot of resources of raw materials, production process produces a large number of sources, material properties and buildings can not reach the same life, in building decoration projects, easily lead to quality problems. The main purpose for interior walls, exterior walls and ceiling of bonding polystyrene board and rock wool board, extruded insulation board and other boards. A: The base requirements: smooth, firm, dry and clean. New plaster layer after at least 14 days before curing and drying after construction (base flatness of less than 2-5 mm one square meter). II: Preparation of material: 25-30% by weight of the feed ratio of added water (add water to adjust the visual basic level and climatic conditions), to stir, mixing materials should be used within two hours. Three: the amount of bonded polystyrene board are 4-5 kg ??one square meter. According to wall formation conditions, the use of the entire surface of the bonding method or the two-point frame method bonding methods polystyrene board. A: the entire surface bonding: flatness requirements apply to less than 5 mm square of a grass-roots level. Plastering with serrated knife to smear adhesive insulation board, then bottom-bonded insulation board on the wall, board formation, pressing seams void. Bonding point box method:: B does not apply to the flatness of less than 10 mm square meters of uneven grass roots. Plastering knife with adhesive evenly onto the insulation board edge, and then evenly distributed on the plate six bonding points, depending on the thickness of the wall painting flatness OK. Then by the above method sticking to the wall plate. The proportion of adhesive mortar with water about 4: 1 (weight ratio)), to stir. Reference dosage: 4 ~ 6kg / m2 primary wall must be flat, solid, clean and dry. Paint layers and layers of loose parts of the primary wall plaster surface must be removed. New painting plaster layer must dry after hardening before use. With a plaster knife to wipe insulation board adhesive mortar, the insulation board and then bottom-kneaded paste evenly to the base wall, the board should be flat, slab should be compacted to void. With 2m by foot inspection flatness, there can glue between the seams. Paste ways: point edge Paste or strips pasted stickers area ≥40% of the entire board area. This product is installed in the brown paper bag, net weight 40 kg each bag. 5 ~ 30 ℃ under the conditions of storage, the storage period of six months, sunscreen, pay attention to water, non-dangerous goods for transportation. Placed on pallets stored off the ground to avoid rain soaked to ensure ventilation and dry. Avoid direct sunlight. Note A: adhesive mortar in proportion with stirring, according to the construction site on the viscosity of the mortar to adjust to. Two: the construction environment and the primary wall temperature of not less than 5 ℃, wind 5 below, to avoid the rain construction. Three: When you paste insulation board even rubbing pressure, not rattling. Four: Paste completed within 48 hours, can not be a process under construction, and should avoid touching, percussion, vibration. Five: In the case of wind or rain than 5 should take protective measures. Six: good mixing mortar should be used within 2 hours, the solidified hardened mortar can not be used a second time. Seven: the construction site is strictly prohibited without permission to add sand, cement and other additives. Excellent quality is the last word company statement, there is no question of powder factory strict quality corporate purpose; user credibility of the first quality first corporate philosophy; the best products delivered to the client company declares : a signed product quality assurance and undertaking - substandard products not manufactured. 2, within two years of product quality tracking service, and customer service records stored in the archives for 20 years. 3 Ensure product quality problems, I will guarantee, refunding, replacement, meet customer requirements.